How to Adjust a Glass Shower Door | No Time? No Money? No Problem!


Articles, products, and services offered on this site are for informational purposes only. We recommend using caution and seeking professional advice. This site provides general information. We are part of the Amazon Services LLC Associates Program, an affiliate advertising program. is compensated for sales resulting from links on our website.

Please review our disclaimer before taking action based on anything you read or see.

This primary article’s objective is to educate us on how to adjust a glass shower door, installing a shower door, and other relevant topics discussed in the article.

How to Adjust a Glass Shower Door

Shower doors are a stylish alternative to the traditional shower curtain, but even less a little maintenance to get a good look. Cleaning is easier to do when you have the doors out of your way, and luckily, there is no need to call in a professional because you can remove them yourself. You can find two types of shower doors, sliding and hinged, and this article will cover how to adjust them.

Step-1: Remove a sliding door

A sliding shower door is the easiest to remove from its frame, as there is nothing to remove. The bottom track is made of aluminum and will have one edge shorter than the other. On the other hand, the top way and the top of the door are where the roller wheels are located. Learn painting a roller door. Most shower doors slide into the cabin, so this is where it should be. Contact the gloves to help you grasp and maintain control of the door. Next, take each end of the door and lift it firmly straight up. It would be best if you got off the track. Now, tilt the top of the shower door towards you and, at the same time, bend your knees. This allows you to control the door while at the top of the track.

Step-2: Remove a swing door.

A shower that uses a typical balance style uses hinges to allow you to open and close the door. To remove this type, you must start within the post to get started. Locate the hinges and use a screwdriver to remove them from the metal frame. Hold the door carefully while doing this to prevent it from falling.

It is good to remove the lower hinge first to maintain a control measure that separates the upper hinge. Once removed, the door is no longer attached and can be removed from the shower stall.

Step 3: Remove the stationary glass.

Many shower door frames have two pieces, the door itself and a stationary shutter. Both must be cleaned. Look at the metal frame along the wall where the standing part is placed. Any caulking that is on the wall first, as this can cover the screws you need to remove. Retake the screwdriver and loosen the screws on the frame once you find them until the stationary glass piece is loose. Remove the part by sliding or lifting it out of place.

Step 4: Remove the aluminium frame.

If your goal is to adjust broken or damaged glass, you should remove the aluminum frame around it after taking the door off its track. Force your utility knife between glass and metal, and slide the blade along the edges. These cut the frame without the adhesive that was used. Do this on both sides. Then use the rubber mallet to tap the metal on the ends to dislodge it from the glass. Now you can use your power to release the aluminum.

Read More: How To Remove Bifold Doors

How to Install a Glass Shower Door

how to adjust a glass shower door

Step-1: Measure the shower opening:

To make sure your shower door fits properly, you need to take three separate measurements: the total length of the threshold, the midpoint of the threshold, and the walls’ height up to 5 feet (150 cm). These measurements will help you find the necessary dimensions for each of the door rails. 

  • Take into account the distance between the shower opening and nearby plumbing fixtures (such as a toilet or sink) to allow adequate clearance.
  • Write down your cabin measurements on a separate sheet of paper in case you need to refer to them at any time during the installation process. 
how to adjust a glass shower door

Step-2: Choose between a sliding door and a swing door:

The style you choose will depend mainly on your preferences. That being said, the size of the shower can affect the look and function of the door.

Read More: How To Install Towel Bar On Glass Shower Door

Swing doors tend to be best suited for small cabs, which are 120 cm (48 inches) or less from wall to wall, where limited space makes it easier to fit a single large door. For cabs that are more than 60 inches (150 cm) wide, a pair of sliding doors will save space by offering a more practical movement pattern. 

  • If you decide to install a sliding door, the measurement for the middle of the threshold point will become necessary, as it is the point where the edges of both door panels overlap when closed.
  • Compare different door sizes and styles to find one that matches your shower stall. 

Read More: How To Install Door Trim With Uneven Walls

how to adjust a glass shower door

Step-3: Cut the base guide to the proper length:

Use a fine-toothed hacksaw to trim the piece of metal to match the threshold measurement. The directory’s size must correspond precisely to that of the sill to fit snugly into the car opening. 

  • A miter box can help you make neater and more precise cuts.
  • Run a metal rasp over the cut ends to smooth them out. Make sure to vacuum up any remaining metal shavings to prevent them from scratching the bathroom floor. 
how to adjust a glass shower door

Step-4: Centers the base guide over the threshold:

Place the piece on the raised point and use a tape measure to measure each side’s same amount of space. Check that the alignment is adjusted carefully, even if it deviates by 19 mm (0.75 inches), as the door is likely not closing correctly. 

  • Mark the location of the base guide with a pencil. This way, you can easily re-center it if it slides while you work.
how to adjust a glass shower door

Step-5: Apply a silicone sealant to secure the base guide:

Once you place the bottom piece where you need it, you need to apply a silicone sealant line to each side to glue it. Apply constant pressure to the base guide for about a minute until the sealant has dried enough to hold it in place. 

  • Most quick-drying sealants will set in 3-12 hours. However, it can take a full day for the adhesive to cure fully. 
  • To prevent leaks, you should avoid showering until the caulk has had time to dry.
installing sliding shower doors

Step-6: Align the jamb on the hinge side with the base guide:

Slide the jamb down into the grooved base guide. It would be best if you waited a minute to make sure it is flush (against the wall) and plumb (perfectly straight). Otherwise, you could end up with small voids in the finished frame. 

  • The hinge-side jamb can be distinguished from the lock-side jamb by the mounting slots into which the door hinge is attached on the inside edge.
  • In most showers, the hinge is positioned on the opposite side of the stall from the showerhead.
  • Sliding doors do not have specific jambs on the hinge side or lock side, but installing the side rails is the same process.
sliding shower door installation

Step-7: Mark the screw holes on the wall:

Insert the tip of a pencil into the holes that extend up the jamb on the hinge side and mark a small dot on each one. These points will serve to indicate where to tighten the screws needed to secure the jamb. 

  • Wax marks show better than graphite on acrylic or tile walls.
sliding glass doors repairs

Step-8: Drill the holes for the screws:

Remove the jamb from the wall and drill the holes with a 3/16-inch (4mm) masonry bit. Each screw hole should be approximately 1.75 in. (44 mm) deep to accommodate the mounting screws. Once you’ve finished drilling the holes, tap the plastic anchors on the wall to protect the shower surface. 

  • You can help to score a notch in the screw holes with a chip or small lump to start. This procedure will provide a shallow seat for the bit so that it is less likely to drift.
  • You need to drill carefully to make sure each hole is perpendicular to the wall.
glass shower door hinge slipping

Step-9: Attach the jamb and tighten the screws:

Place the frame piece against the wall; align the screw holes with the ones you just drilled. Have a helper hold the jamb firmly as you insert a 1.5 inch (38 mm) pan head screw in each hole and tighten it down. 

  • You should drill slowly to avoid applying too much pressure. This procedure can generate stress fractures in the surrounding frame.
sliding shower door installation

Step-10: Repeat this procedure with the jamb on the side of the lock:

Line up, mark, drill, and position the wall jamb on the opposite side just like you did at the beginning. Once you’re done, you should have assembled 3 of the four frame pieces.

  • Don’t forget to plumb and flush the piece and insert the wall anchors before tightening the screws.
  • The structure of the jamb on the lock side is simpler than that on the hinge side. Typically, it is an “L” shaped piece that acts as a doorstop.
sliding glass doors repairs

Step-11: Measure and cut the header rail:

Close the shower door and extend the tape measure from side to side. Mark the dimensions on the head of the frame and use the hacksaw to cut it to size. Smooth the raw edge with a metal rasp. 

  • It is essential that you measure and cut the top rail separately rather than duplicate the base rail dimensions. It may not be the same width as the bottom of the frame. 

Step-12: Attach the head to the top of the frame:

Raise the top rail at the leading edges of the door and adjust it until it slides into place. If the head you are working with has screw holes on end, you should adapt them for added security. This piece will complete the fourth and final side of the frame.

  • Many shower door heads have slots to fit into the jambs’ top, without the need to attach them to the frame separately.
  • If you have a swing door, you want to make sure the head’s shorter arm is pointing outward so the door can be opened and closed freely.

Understanding the Concept of Sliding Door

Sliding doors are a revolutionary invention, which differs from any door that exists. Their sliding function has positioned them at the highest standards for interior and exterior decoration.

A sliding or sliding door opens horizontally, either from left to right (depending on the position in which it was installed). Its functionality lies in its rail system, made up of wheels, the rail itself, and fittings that ensure this, which will allow the sliding door to move from one side to the other at your convenience.

Although these products abound in interiors such as living rooms or kitchens, these products also have excellent bathroom decoration potential both as an entrance to it, and for showers.

Sliding bathroom doors are made of materials suitable for the environment and resistant to the most common component in any bathroom: water and humidity. Its most used materials for this manufacture are glass and PVC (incredibly resistant and durable plastic).

Guide to Buying Sliding Doors for Bathrooms

It is essential to keep in mind what best suits your bathroom. While you want a sliding glass door, they offer a more delicate and elegant look. A PVC door is also an option to consider, as this plastic material is impressively resistant to impact, fire, and moisture. So don’t worry, because, in this area, the materials are the best able to withstand the water and humidity of a bathroom. ELEGANT Double Sliding Bypass Frameless Shower Door is one of the best Sliding Bypass doors on the market.

ELEGANT Frameless Shower Door 60'' W x 72'' H...
7 Reviews
ELEGANT Frameless Shower Door 60'' W x 72'' H...
  • 【Shower Door Dimension】- 60'' W x 72'' H. Walk-in: 28 7/10''. Up to max 3/5 in. of adjustment for width by cutting top rail guide, if needed.
  • 【Safety Heavy Clear Glass】- Clear 3/8 inch (10 mm) tempered safety glass - ANSI Z97.1 certified, resist high temperature, no shatter and easy to clean.
  • 【Humanized Handle Design】 - with 2 long towel bars, you also can go in/out conveniently, also can put clothes and towels on it. very practical.

Whether in glass or PVC, the designs and colours abound, hand in hand with the brands that we will present to you later, which have been dedicated to the manufacture of doors for many years, within them there is a unique touch only for sliding doors for bathrooms. So when you see a design that catches your eye, don’t doubt that there will be more than one colour and size that will suit the dimensions of your bathroom.

The prices are typical of a market with plentiful supply and demand, where each brand competes with the others to offer you the best in these products. Without more or less, let’s see what’s out there.

HOMCOM Sliding Glass Door Sliding Glass Door Interior Doors Barn Door 75x210cm


✅The high-quality aluminium track allows the door to slide smoothly and safely

✅The glass door is 8mm thick, so it is a durable and robust sliding door.

✅It has a stainless steel handle that allows the door to be opened and closed easily.

✅Includes guide, handle, and mounting hardware

✅Total dimensions: 75x210x0.8cm (LxWxH). Max capacity rail load: 90kg

HOMCOM 6' Rustic Interior Sliding Barn Door...
54 Reviews
HOMCOM 6' Rustic Interior Sliding Barn Door...
  • 2-Door Hanging Rail: Industrial sliding barn door hardware kit will change the traditional barn door into a sliding door, that is useful and practical. Fits for two barn doors with a thickness of 35-45mm and 40-45mm
  • Security Assurance: This barn door hardware kit is made of quality carbon steel for strength, which can hold a maximum of 220 lbs.
  • Space Saver: Saving space is a piece of cake with this classic sliding barn door. Multiple rooms can be opened without the hassle of swinging doors.

HomCom Sliding Glass Door without Work – Satin Glass – 205×102.5 cm


✅This translucent glass sliding door is ideal for your office or at home and is very practical – The sliding door allows light to enter your room – The wheels with rubber-coated ball bearings guarantee silent sliding when opening and closing the door.

✅Rubber-coated ball-bearing wheels on the carriage ensure quiet gliding when opening and closing the sliding door.

✅Includes the guide, handle, and mounting accessories -Assembly instructions -Tips: Install the glass door so that the handle is fixed well.

✅The sliding door allows light to enter your room and saves space -Safety glass with rail fixing and with all its fixings.

✅Total dimensions: 200×213 cm (LxH); Rail dimensions: 2000x105x44.8 mm (LxHxW); Door dimensions: 102.5×205 cm (LxH);

HOMCOM Vertical 24' x 16' Stainless Steel Bathroom...
97 Reviews
HOMCOM Vertical 24" x 16" Stainless Steel Bathroom...
  • STYLISH, COMPACT CABINET: This HomCom two door, glass front stainless steel floating display cabinet creates a polished, clean look and gives you the ability to store and display personal hygiene essentials in a bathroom, or trinkets, awards, or other items throughout your home or office.
  • AMPLE STORAGE OPTIONS: Three fixed interior metal shelves provide multiple levels of storage within this reflective medicine cabinet, the metal surface adding depth and an artistic touch when colorful items are stored in the cabinet.
  • REFLECTIVE SURFACES: This cabinet is made from highly polished reflective stainless steel on both outer and inner surfaces, creating a reflective mirrored surface that you can use as a mirror or just enjoy the reflection of the room around you.

HOMCOM Sliding Glass Door Glass Sliding Door Interior Doors Barn Style Barn Door 75x210cm


✅The high-quality aluminium track allows the door to slide smoothly and safely

✅The glass door is 8mm thick, so it is a durable and robust sliding door.

✅It has a stainless steel handle that allows the door to be opened and closed easily.

✅Includes guide, handle, and mounting hardware

✅Total dimensions: 200x213cm (LxAN). Door dimensions: 75x210x0.8cm (LxWxH). Max capacity rail load: 90kg

Last Words

We have reviewed everything we need to know about that essential part of our home’s interior on how to adjust a glass shower door and other relevant topics discussed in the article.

Comments are closed.