How to Change Light Bulb in Ceiling Fan | Simple 5 Step Guide
A ceiling fan is a great way to make any room more enjoyable. It can also help reduce the cost of heating and cooling your home. When you have a burnt-out light in the ceiling fan, replacing a real light bulb is usually the easiest part of removing, the light cover can be a real trick. Let’s find out how to change light bulb in ceiling fan.
How to Change Light Bulb in Ceiling Fan
You will also have to choose between a light bulb, an LED, and a halogen, to name a few.
It is a good idea to gather all your tools for all projects. Here is a list of what you will need to replace your bulb.
- paper towels
- Window Cleaner
- headlamp or flashlight if necessary
Read More: How To Change Light Bulb In Ceiling Fixture
Switch Off the Light Switch
Let’s start by turning off the light switch. Allow the bulb to cool completely for about 10 minutes. Many light bulbs become very hot and can burn your fingers. The plate does not need to be removed. Just turn off the button and check if the light is on.
Unscrew the Old Lamp
Grab the ladder and, if necessary, the headlamp or flashlight, and carefully unscrew the old bulb to the left. Be very careful because the glass in the flask is thin and can break easily. If the bulb does not extend easily, twist it slowly and gently as it rotates.
Clean your Light
This is the perfect time to give your good light cleaning. You can use a glass cleaner. Or, if the globe falls from the ceiling, take it to the sink and wash it with warm water and a mild detergent. When installing a new bulb, rinse it with hot water and dry it.
Install a New Bulb
Now it’s time to put on a new light bulb. Let’s start by looking at the end of the light bulb. You will see a threaded metal piece at one end of the bulb. This piece will go into the ceramic threaded hole in your lamp. Then look for a ceramic hole with a threaded metal piece inside.
However, if you do not remove the old bulb, simply place it in the hole and screw it straight.
Remember to be gentle and shake lightly when turning the bulb. Do not tighten too much. The light bulb was installed as soon as it seemed to stop threading. Then turn on the power switch to make sure the light works.
How to Replace a High Ceiling Bulb
Things you will need
- Gripping pliers
- Protection glasses
- Replacement bulb
Switch off the wall switch on the luminaire with the defective bulb. To safeguard your eyes, put on a pair of safety goggles. Often these bulbs have not been replaced for some time. When replacing the bulb, debris and dust will fall from it. These particles will be shielded from your eyes by goggles.
Unfold the hook until it is fully extended. Some gripper pliers use a twisting motion to extend the gripper arm.
Place the gripping jaws or suction cup on the end of the bulb and press the shutter handle to open the jaws or extend the suction cup. Place the end of the pliers on the bulb around the perimeter of the bulb until you feel resistance. Slowly release the trigger to engage the jaws or suction cup.
Turn the pliers counterclockwise and unscrew the bulb from the socket. Gently lower the end of the gripper and remove the bulb from the tool.
Place the new bulb on the gripping tool’s end and lift the bulb’s end to the socket. Screw the bulb into the socket by turning the pliers clockwise. It will take a little patience, especially when you first use the tool. Continue turning until the bulb in the socket is no longer easily rotated. Do not try to tighten any further, as this may cause the bulb to burst.
Press the trigger handle to open the jaws or release the suction cup. Fold to save the clip. Turn on the luminaire wall switch.
How to Replace a Ceiling Fan Light Fixture
Switch off the power
Find the circuit breaker panel on your property. Turn off the ceiling fan and lighting set’s circuit breakers. Toggling the switch to the right usually deactivates circuit breakers. In a room with a ceiling fan, turn off the light switch as well.
Remove the Light Fixture that is currently in place.
Remove the globe and bulbs from the existing light set. Locate the screws that keep the existing fixture in place to do this. Using an appropriate screwdriver, loosen the light set mounting bolts and lower the light set away from the ceiling fan motor.
Existing wiring should be disconnected.
Two wires lead to the luminaire if your ceiling fan is connected to both the fan and the lights. Remove the wire nuts from the wires to detach them. Turn the caps counterclockwise to disconnect these wires. Place the caps in a safe place.
Get rid of the outdated light fixtures.
Disconnect the wires and remove the tool once both covers have been removed. Remove the old set of lights from the room. Make a mark on the wires to ensure that they are connected to the proper location in the new fixture. Try to connect the new light set’s connectors,
Replacing the old light fixture with a new ceiling fan light fixture and then reversing the previous three stages pass the wires through the hole in the new fixture’s center plate. Reinstall the wire caps on the new fixture’s wires.
Ensure that the new set of lights is in place.
Hold the new luminaire in place and secure it by screwing the light assembly together once the wires have been attached.
Reconnect the ceiling fan’s power source.
Turn on the circuit breaker that controls your ceiling fan in the circuit breaker cabinet. Check to see if the light is switched on. Please turn on the fan to make sure it’s operating.
Frequently Asked Questions
How do you remove the ceiling bulb?
Hold the long tube bulb with both hands and turn it 90 degrees or 1/4 turn counterclockwise. This aligns the pins with the slots in the sockets to remove the bulb. Lower one end into the socket and remove the bulb from the holder.
Is it easy to replicate the ceiling fan’s light cover?
Ceiling fans often come with a mounting flange under the fan motor, in which an optional set of lighting can be placed. In many cases, you can replace the light set that comes with the ceiling fan with a different light style.
How to remove a light bulb?
Grasp the bulb lightly but firmly, gently push upwards and turn counterclockwise until it disengages from the socket. Continue turning gently counterclockwise until the bulb is released from the socket. Replace the bulb. Insert the spare bulb lightly but firmly into the socket. Restore power. Discard the old light bulb.
Are there any special bulbs required for ceiling fans?
If your ceiling fan light is the only light source in the room, you will need a light bulb that provides as much light as possible. Anything under 800, such as a standard 60-watt light bulb, won’t be bright enough to illuminate the entire room.
Why don’t the LED bulbs in my ceiling fan work?
Make sure the lights are securely fastened in their sockets. Check that the bulbs have the correct wattage for the ceiling fan kit. Check for a malfunctioning bulb by burning in the work light. Replace burned-out bulbs with new bulbs with the correct wattage.
Why is my ceiling fan constantly blowing out the bulbs?
Another cause of the bulb burning out is the excessive vibration of the luminaire. A good example of this is a ceiling fan with a luminaire. The fan begins to shake as the blade becomes imbalanced, and the vibrations disturb the bulb filament, shortening its life. You can try a light bulb with heavy traffic to solve this problem.
It may appear that changing a light bulb is a simple procedure. However, you work with electricity, and the most important thing to remember while dealing with this issue is to keep safety regulations in mind. Hope you have learned how to change light bulb in ceiling fan.