How to Cut Granite Backsplash | A Step By Step Guide

This article’s primary objective is to educate us on how to cut granite backsplash.

Granite is one of the most versatile materials in the world. If we think about its origins, then we have to say that it is a plutonic igneous rock, formed by the slow cooling of magma (molten aluminum) at great depths of the earth’s crust.

How to Cut Granite Backsplash

The kitchen is the heart of the home, but it can be depressing when you don’t like your granite backsplash. Due to its upright position and prime location, the backsplash sets the tone for any kitchen.

If you are looking to cut your kitchen granite backsplash for some reason – maybe it’s old, maybe it’s outdated, maybe it’s not to your liking – this guide is intended to provide you with useful information before you begin.

Cutting your Granite backsplash can be remarkable, relying upon your tile, its age and type, the establishment strategies used, and an assortment of different elements. Here we provide step-by-step instructions to cut granite backsplash.

How to Cut Granite Backsplash: Material Required

  • Crowbar, wood chisel
  • Hammer
  • Multifunctional tool (Dremel)
  • Safety glasses, gloves (optional, but recommended)

Prepare the kitchen sink

Before you begin, get rid of everything on your kitchen counter. Whichever method of removing the tiles you choose, it will get dirty.

Repair of certain plasterboards

Also, be aware that the chances of having to repair parts of the drywall or replace them entirely are quite high. Prepare for this possibility now, before you begin, so that you don’t get completely frustrated if (or rather when) it happens. 

It’s time to start! 

Start by cutting the faceplates and sources introduced on the tiles to be taken out. Then cover all the countertop surfaces with drop cloths or some protective coating.

If you need to remove tile near the kitchen sink (probably if you are removing a kitchen granite backsplash), put the plug in the sink drain. This will prevent tile pieces from falling into the sewer and clogging it or damaging the drainage system.

Method 1: Remove the tiles individually.

Starting at an easy access point (for example, on one side of your backsplash), carefully tap a wood chisel with a hammer between the back of the tile and the wall.

This method is recommended when the tile itself comes off fairly easily, leaving little or no damage to the wall.

Keep eliminating the tiles, working from start to finish, until the entire tiles are taken out. This method may seem tedious, working one tile at a time, but it will likely save you time in the long run as your drywall repairs will be minimal.

But what happens when, during the removal of your first tile, it rips an entire piece of the drywall with it? If so, it can cause significant damage to the wall and continue? Thus removing one tile at a time is not an option at this stage.

How to Cut Granite Backsplash

Method 2: Remove large, strategic pieces of tile and drywall.

Be careful. This method will require you to replace the entire section of gyproc behind your granite backsplash. Using a small Dremel-type circular saw cut the drywall all around the granite backsplash.

You will need to cut the joint between the countertop and the bottom row of tiles. Be careful with your multi-tool next to the counter to not to damage the surface of the countertop.

Cut along the side of your backsplashes, from the top of the countertop to the top row of tiles. Be careful not to cut the structure of the wall itself.

Then it would help if you cut under the hanging furniture with this tool. You cut all of the “walls” of your granite backsplash. Cut all around the backsplash, then gently pull outward, starting at a corner. 

If you’ve carefully cut everything out, you should remove a large piece of tile and the accompanying drywall all at once. At this point, you should see your insulation or your wall framing.

Continue this method. Cut the edge of the tile backsplash totally through the drywall. At that point, delicately pull to eliminate huge pieces. Do this all along the rest of the granite backsplash until it is completely removed.

how to cut granite by hand

Method 3:

Every tool is a hammer!

Cut the tiles with a sledge, eliminate them, and eliminate the drywall in pieces. This technique is untidy. Plug your sink! And wear gloves and safety glasses! But it’s an effective method if you can’t trim the perimeter of your backsplash for some reason.

Note: ALWAYS use caution when demolishing, especially around electrical or plumbing components.

Once this job is done, pick up the large tile shards, vacuum the rest, mop and scrub everywhere else. Congratulations, you have just removed your granite backsplash. You have just taken another step towards creating the kitchen of your dreams! Perhaps removing a granite backsplash is a job that shouldn’t be overlooked. You may need to hire a professional granite backsplash installer.

How to Cut Granite

Granite contains thick and hard stone, so you should be persistent and set up the appropriate devices for the work. It should be noted right away that you should not save on diamond discs for a grinder, buy it for cutting granite, and not for metal or reinforced concrete.

Any cutting of stone, no matter whether it is granite or travertine marble, is carried out using a diamond tool, therefore this type of stone processing is called diamond cutting.

how to cut granite with a grinder

Cutting Granite Slab or Tile

Step 1

Start by cutting granite yourself, prepare all the important material. For cutting granite, a conventional grinder with a diamond blade for cutting stone will work, but a diamond saw for dry and wet cutting is still the best option. Any of the above tools will do the job, but a wet cut diamond saw will produce very little dust thanks to a small pipe that drops water onto the granite surface when cutting. To make it easier to clean up afterward, cut the granite slab outdoors if possible. 

Step 2

Spot the stone piece on a robust surface and use C-clasps, connecting each 10-15 cm at the perimeters of the section to form sure about it safely. By protecting the give clasps, you’ll be able to decrease vibration and development of the rock surface, which limits chipping and breaking. 

Step 3

Secure yourself by wearing a respirator, wellbeing glasses, gloves, and hearing assurance. If you are cutting stone without a wet diamond saw, be prepared for an abundance of dust and a very loud grinder sound.

Step 4

Apply covering tape to the bit of stone that you expect to cut. . Simply place some strips along the highest within the regular territory where you’ll cut – you’ll be slicing directly through it.

Step 5

Measure carefully and draw a line over the tape. The idiom of the astute woodworkers: “Measure multiple times – cut once” is applied here. Take as much time needed and twofold checks your estimations to ensure you will be cutting in the perfect spot. Remember, in the process of cutting, 2-3 mm will go along the marking line, so take this into account in your work. When cutting granite, you only a chance in caring for business.

Step 6

Spot the precious stone edge set apart for cutting rock on the saw. At that point make a short “cut”, around two centimeters in length, from the finish of the cut line. This will diminish the danger of stone chips showing up when cutting from the opposite end and arriving at that point. Little cuts are basic on the grounds that the rock surface turns out to be slender not long before the saw edge gets through the last bit of stone toward the finish of the chunk. Without cutting, vibration from the saw can chip or even sever the piece. 

Step 7

In the wake of cutting, return the saw to the furthest edge of the board and cut gradually along the cutting line. Ensure you keep the edge absolutely lined up with the cut line, and keep up the light and consistent tension on the saw without pushing it, permitting the cutting edge to do the work. Use a similar light pressing factor until you complete the cut. Without cutting, vibration from the saw can chip or even break off the piece.

Step 8

After cutting, return the saw to the other end of the board and cut slowly along the cutting line. Concentrate on keeping the blade precisely aligned with the cut line, and maintain the sunshine and constant pressure on the saw without pushing it, allowing the blade to try to the duty. Use the identical light pressure until you complete the cut. This might take quarter-hour or longer looking on the length of the cut.

Step 9

Peel the tape off the granite and admire your smooth, clean cut. Let the stone dust settle and remove it with a construction vacuum. If you’ve used a wet saw, you will find liquid slurry instead of dust; wipe off the stove with a damp cloth. The slurry left on the sidewalk or driveway are often easily washed off with a garden hose

Granite Cutting Tools

On the other hand, depending on the type of cut we need to make and the thickness of the granite, it will be necessary to use a different type of machine to cut granite and disc. As for granite cutting tools, it can be cut with a radial or manual granite cutting machine, granite can also be cut with a water cooling tabletop cutting machine.

For cutting with a table granite cutting machine, you can use the wet granite discs. By cutting with this system, you can achieve precise and effortless cuts, even up to considerable thicknesses depending on the machine. If instead, we talk about dry cutting to make cuts in a thickness of up to 3 cm with maximum precision, turbo granite blades can be used, which offer good cutting power and allow the narrowest cut possible for this material. This is a granite cutting disc that allows small but precise cuts. As a recommendation, when you have to make many cuts or cuts that are very long, it is best to stop so that the disc cools down and does not reach high temperatures.

When cutting dry and making large or many cuts, even in thicknesses greater than 3 cm, you can use the reinforced granite disc.

granite cutting tools

How to Cut Glass Tiles

Glittering beauty glass tiles add a lot to a backsplash or mosaic. Adhere to these guidelines to cut glass tiles of different shapes and sizes.

Steps 1 – Preparing the work area

When working with glass tiles, be sure to lay down a plastic or wood cutting board if you don’t have a specific worktable for cutting the tiles. A wheeled tile clamp is that the cheapest and simplest tool, working sort of a clamp, but not doing o.k. at making precise shapes. It also often leaves jagged edges. A tile marker works well for much standard thickness (4mm) tiles. If a glass tile is simply too thick for a scorer, a wet saw is used. This saw should be used with a diamond-encrusted blade specially designed for glass tiles. For many purposes, a tile marker does a beautiful job making lots of various shapes. Read on for more details on using the tile marker.

how to cut granite for sink

Step 2 – Glue the tile at the underside

While not necessary, sticking your tile to your chopping board or table can prevent mistakes by keeping it still.

Step 3 – Mark a cut on the tile

Using the tile marker, mark (engrave) a cut along the face of the tile, moving slowly with even pressure along with the tile. Use a ruler or ruler to help you with straight lines.

There are many alternative qualities of tile. The more professional grades will release some oil on the tile so the blade cuts smoother and deliberately. The sort of shapes you’ll be able to make will rely upon the standard of your marker. Practice on the waste tiles first.

how to cut granite countertop in place

Step 4 – Clip the tile

There are several ways to separate the tile into two pieces. First, you’ll hold it in two hands and bend it in order that it comes loose from you. If you scored a line, you’ll be able to use tile pliers to complete the task, lining up the pliers on the blade with the score on your tile. Or, you’ll be able to place a wire under the tile, lining it up with the cut (which is on the other side), and so press firmly from the highest of every side of the tile to the underside. Finally, you’ll place 1/2 the tile on the sting of your table, and gently tap the half that’s not supported by the table with a tool. Confirm the tile doesn’t fall on a tough floor, but on a carpet or blanket so it doesn’t break or leave a scar.

how to cut marble

How to Cut Granite Backsplash: FAQ

What is the best tool to cut granite?

The use of Tyrolit brand discs, allow clean and straight cuts, both in granite and in porcelain materials, working dry through a machine radial. They do not cause chipping and have a very long service life.

Can I cut granite myself?

Yes but you must equip yourself with protection. Also, get a vacuum cleaner to limit the spread of dust when cutting.

How do you smooth cut granite?

It is necessary to use specific instruments equipped with a diamond blade. A machine for cutting granite must be able to complete all phases of work in complete safety, in compliance with the standards in force. A machine for cutting granite of low quality can have dramatic consequences and lead to unnecessary expenses due to the many breakdowns and the continuous maintenance it requires. Choose only certified manufacturers, the only ones who can offer you reliable and safe machines to smooth cut granite.

Last Words

We believe you enjoyed reading through this article on how to cut granite backsplash and other subtopics discussed in the article.

Read More: How to Cut Mosaic Tile

Comments are closed.