How to Paint Baseboards with Hardwood Floors | Step By Step Guide

This article’s primary objective is to educate on how to paint baseboards with hardwood floors, painting baseboards, and other vital subtopics discussed in the articles’ context.

How to Paint Baseboards with Hardwood Floors

Step-1:

Sand the baseboards with fine 180 grit sandpaper. This progression is particularly significant when working with baseboards that have just been painted with sparkle paint. Rub fine (180 grit) sandpaper wrapped around a block of wood in small circles on the baseboards to create a rougher surface on the baseboards to which the paint will adhere.

Step-2:

Apply a coat of oil-based primer to the baseboard. Using your 2.0 ” angled paintbrush, apply a coat of primer to the baseboards. Ensure you make use of an oil-based primer to enable it dry for a day with good durability. This will help the paint to adhere to the baseboards.

Step-3:

Vacuum the dust from baseboards and your workspace. Sanding produces a great deal of residue, so put forth a valiant effort to eliminate everything before you begin painting. Vacuum the floor or rug where you were sanding. Give exceptional consideration to the little break between the baseboards and the floor, as this is an infamous residue cover. 

Step-4:

Clear all furniture from the entry. Move the entirety of the furniture in the space to another room, or if nothing else, away from the quick territory where you will paint. It isn’t vital to cover the furnishings, yet ensure it is a distance of ⁄3 to 1 m (2.2 to 3.3 ft.). 

Step-5:

Treat any uncovered wood with a tying arrangement. Ensure you check whether baseboards have never been painted. Make use of a paintbrush to tenderly brush 1-2 layers of a tying arrangement onto the woods bunch (dull spots). Leave it to dry for 24 hours. 

Step-6:

Sand any blemishes in the paint using additional fine sandpaper before applying your subsequent coat. Sand away any air pockets or parts of the paint that are not smooth. Else, they will possibly deteriorate when you put on the subsequent coat. Use extra-fine sandpaper (240, 320, or 400 coarseness). 

Step-7:

Pick an oil-based semi-shine paint. Oil paint is suggested for baseboards because, even though the drying time is longer, it’s thick consistency helps fill in breaks and joints in baseboards and opposes wear for quite a while. Abstain from using a level emulsion for painting will bring about plinths that can without much of a stretch be set apart out.

Step-8:

Cover the zone where the divider meets the baseboard with concealing tape. Delicately press 2 inches (5 cm) of veiling tape (likewise called a blue tape or painter’s tape) on the divider only over the baseboard. So if your brush incidentally pulls from the baseboard, your divider will be secured. 

Step-9:

Pluck the zones between the brush strokes. With each brushstroke, you should plunge your brush in the paint. Nonetheless, for zones between strokes, lift the brush marginally and softly apply the plume paint to dodge cover marks (denotes that show where one brush stroke finished and another began). Fletching includes delicately using the tip of the brush to make smooth progress between various brush strokes. You won’t require a great deal of paint on your brush to do this. 

Step-10:

Plunge your brush about 33% of the time in the paint. Make use of a 2.0-inch calculated paintbrush. You don’t need it to be over-burden with paint, so brush it against within edge of the paint can to eliminate an overabundance. 

Step-11:

Ensure the floor with covering tape. Putting paint on the floor is likely the exact opposite thing you need. When your room has hardwood floors, place covering tape segments on the floor where the baseboard meets the floor, do this for the entire room. 

Step-12:

Similarly, apply brush strokes in the center of the plinth. Hold your paintbrush around a 45-degree point and apply the paint one way on the most stretched out piece of the baseboard. Go gradually. When you noticed that the paint is dribbling where it should trickle on the board, blend it up before it dries and structures a knock. 

Step-13:

Begin painting from one corner of the room. Check whether you are given the correct paint to use. Paint from left to right. This will kill the requirement for gracelessly situating your body and limit your odds of dribbling paint on the floor. 

Step-14:

Paint your subsequent coat. You may have to paint multiple coats; White is the most mainstream tone for baseboards, so that you may end up in the present circumstance. Ensure you use coats and sands.

Step-15:

Cut the edges of the plinth. Begin painting on the adjusted top edge of the baseboard using a stroke called a cut. Hold your brush so the fibers’ wide side confronts the floor and slides the restricted end along with the highest point of the baseboard. At that point, rehash this cycle for the lower part of the board. 

Step-16:

Brush on polyurethane stain. This progression is discretionary, yet polyurethane stain assists baseboards with opposing scratches and scrapes longer. This is suggested if you are painting the baseboards in a home with little youngsters or pets. 

Step-17:

Permit the paint to dry for 24 hours. You should paint it with two coats, even when you cover a lighter tone up a more obscure tone. Give the first 24 hours to dry, or follow the drying time as coordinated on the paint jar. 

Step-18:

Clean the baseboards with a wet wipe. Make use of water and non-soapy detergent inside a bucket (i.e., Dirtex, Spic)

How to Paint Plastic Baseboards

• Choose the color. Baseboards should generally be the same shade as the walls. Darker baseboards will give a more modern and contemporary look to your spaces, while lighter colors will make small spaces look bigger. If you still have doubts, play it safe, and opt for pure white.
• Choose the brush. For most skirting boards, the ideal brush is 5 cm. If you use water-based paint, be sure to use a brush with synthetic bristles.
• Sand the surface. This allows the paint to adhere and prevents future flaking. Use a soft, dry brush to remove paint and dust.
• Create a clean base. If the baseboards are chipped or dirty, clean them thoroughly with hot soapy water (you can use detergent or caustic soda).
• Protect the edges with tape. I covered the skirting board’s edges with masking tape to achieve clean lines with a professional finish. If the floor is carpeted, use a putty knife to sink the end of the tape. This will ensure that the paint does not “slide” under the tape.
• Start painting. Dip the bottom half of the brush into the paint to load it, remove excess paint. Begin to apply the paint evenly over the baseboard, covering one meter long sections. Always apply the last brushstroke along the entire skirting.
• Apply the second coat. Solvent paints dry in 24 hours, but water-based paints take less time, so follow the recommendations printed on the can before applying the second coat—no need to sand between coats.
• Remove the tape. Wait for the second coat of paint to dry completely, and carefully remove the masking tape. If you’ve placed masking tape on the carpeting, press the tape’s edge to “peel” and remove it. You will reveal your wood baseboards painted to perfection. 

How to Paint the Baseboards

Are you thinking of updating your skirting boards? Do not hesitate! Baseboards can have a lot of effects! It’s not only the design that counts, but also the color. Well-maintained baseboards give a home a much more professional finished look. If you want to transform your baseboards, below is the best way to prepare and paint them.

Sand and dust the blades

Before applying a new coat of paint, be sure to sand the previous one. Work across the boards with a sanding block and sandpaper. After sanding the surface layer, clean the blades with a duster. The paint will adhere much better to the wall, without flaking. Have you recently treated your wood floors with oil? No problem, just clean the baseboards with white spirit before painting.

Mask the edges

Mask the edges before painting the baseboards. Place a sheet on the floor and secure it with masking tape along the wall. Masking the baseboards will allow you to create crisp lines. In a carpeted room, the paint may slip under the masking tape. To avoid this, all you need to do is take a paint scraper or other tool with a blunt edge and press down on the tape.

Get started

Start painting your baseboards. Dip your paintbrush in your chosen paint, covering the bristles about a third of their length. Wipe off the excess paint and start painting the baseboards first from the top.

Fill in with the chosen color.

Fill the plinths with the chosen colors. Apply the paint evenly in sections one meter long. Once you’ve painted the entire blade, finish with full-length brush strokes for the smoothest finish. If you have trouble deciding on a color, remember that light colors can make a small room appear larger while dark colors have a more contemporary feel. 

When in doubt, crisp white is always a good choice. Give the slides enough time to dry. Solvent-based paints can take up to a day to dry completely, while a few hours is enough for water-based paint. Follow the jar’s directions to find out and check after the waiting period to see if a second coat is needed. 

Remove the masking tape.

Remove the masking tape before the paint is completely dry to achieve crisp lines. If the carpet was also protected with masking tape, press the tape’s edge to break the seam and reveal a perfectly painted baseboard.

Necessary material Used: 

• Sanding block
• Sandpaper
• Feather duster
• Adhesive & masking tape
• 5 cm flat brush
• Paint for woodwork
• Protective glasses
• Protection’s mask
• Gloves

How to Paint baseboard With Carpet

Correctly and carefully, painting your interior spaces can help make your bedroom look more pristine. Interior paint jobs that look professional have been carefully cut into the baseboard. Cutting-in is when painters apply paint to trim, baseboards, and crown molding without using painter’s tape or getting the paint on the wall. Professional and do-it-yourself painters will want to cover their carpet with a drop cloth to ensure that it doesn’t get stained with paint.

Instructions

• Place a drop cloth on the carpet of a half-inch of the baseboard.
• Tape the drop cloth to the carpet with painter’s tape that is at least 1 inch wide. Lay the strip so that the exposed half-inch of the carpet is covered. This will ensure the drop cloth stays in place.
• Dip a 2-inch-wide brush in the paint so that the bristles are covered half – brush height.
• Slap the brush against each side of the interior of the paint canister. This will remove much of the paint, which will prevent you from applying too much to the baseboard and causing drips to the carpet.
• Paint a long bottom band around the plinth, the center a quarter inch from the plinth’s top.
• Dip and slap the brush again.
• Paint another long strip down the center of the plinth about a quarter inch from the baseboard’s bottom. This strip will overlap first.
• Dip and slap the brush.
• Paint the top of the baseboard by carefully weaving the brush towards but without touching the wall.
• Dip and slap the brush.
• Paint the baseboard’s bottom by carefully weaving the brush down towards but without touching the strip on the carpet.
• Immediately slide the brush across the entire surface to even out the brush strokes. Do not reapply the paint.
• Allow the baseboard to dry completely before pulling the tape and removing the drop cloth. Completely dry paint will not be tacky.

Conclusion

We trust you have taken in a great deal concerning this article concerning the best way on how to paint baseboards with hardwood floors, painting plastic baseboard, recommended tools used to paint baseboard with hardwood floors, and other vital subtopics discussed in the articles.

Read More: How to Remove Slate Floor Tiles