How to Repair a Garage Door that Closes Then Opens Again

Disclaimer

Articles, products, and services offered on this site are for informational purposes only. We are part of the Amazon Services LLC Associates Program, an affiliate advertising program. Amazon.com is compensated for sales resulting from links on our website.

Please review our disclaimer before acting based on anything you read or see.

It is important to understand how all the parts of a garage door opener help lift a heavy door and close it smoothly so that no occupants may suffer injuries. The door slides on rollers on metal guides on each side and the opener, powered by a 1/2 hp to 1 hp electromotor, lifts the door. In this guide, I will discuss how to repair a garage door that closes then opens again?

However, without a pair of torsion springs at the top of the door, it would not be strong enough to perform its function. You can control the opening by a button on the wall and a simple remote control you have in your car.

This one operates the motor via a control panel in the motor housing. Security sensors on both sides of the door complete the picture. If a door isn’t working properly, you can usually diagnose the problem by systematically checking the various garage door components. In this post, we will discuss how to repair a garage door that closes then opens again.

How to Repair a Garage Door that Closes Then Opens Again?

How to Repair a Garage Door that Closes Then Opens Again

Garage doors are probably the most frequently used entrance to your home. So it’s important to maintain them regularly to ensure safety, comfort, and peace of mind. A common problem for many homeowners is that the door closes.

With a simple push of the control panel, and opens again immediately when the door touches the floor. This malfunction can be annoying, especially if you want to get out of the house and the garage door needs to close. The cause is usually easy to find and fix.

If your garage door keeps opening and closing, there are usually several possibilities. If your garage door gives way when you lower it, check the following three common causes and try to solve the problem.

Learn More: How To Paint A Roll Up Garage Door 

The track length is not set correctly.

When you install a garage door opener, it comes with a program and a number that indicates how far the door must travel before it closes completely if the door closes before it reaches the programmed distance.

The opener assumes something may be wrong and automatically retracts to prevent property damage or injury. This setting may be incorrect, or weather conditions may cause the door to expand and contract, affecting the distance the door travels when it rotates. To correct this movement, locate and change the garage door handle set.

Limit switch failure

As with the motion adjustment, the limit switch determines where the door stops when it opens or closes; if the door changes direction, you can adjust the limit switch.

Learn More: How To Make Wooden Garage Doors

Logic board condition

The garage door opener logic board controls all garage door functions. Although garage door openers last for long life, garage door opener components, such as the logic board, may begin to wear out after ten years.

If the logic board expires or starts working wrong, the door may lift and fall unexpectedly. Check that nothing is blocking the door from closing before adjusting the garage door handle with a ladder and a flathead screwdriver.

Garage door openers manufactured after 1993 must be equipped with photoelectric sensors at the bottom of the track. That detects objects in the path of the descending garage door and instructs the operator to reverse the direction of door travel. If the photocell is not in place or if it detects an object, the door won’t close.

Learn More: How To Reset A Craftsman Garage Door Opener

Comparison between Sectional and Roller Garage Doors

Comparison between Sectional and Roller Garage Doors

Legacy garage doors have a single panel. However, many landowners prefer the conveniences of a roll-up door over a sectional door with a single panel.

There are many differences between traditional doors and roller doors. In addition to price, you need to consider installation, materials, and durability. First, let’s look at the main differences between these types of sectional doors. Choose the most convenient system for your home depending on the following factors.

The room

  • Door rails take up space from the ceiling and reduce the ceiling height.
  • When the door is open, much of the ceiling is blocked, limiting space for lighting, sprinklers, HVAC components, or storage. Roller doors eliminate this problem.
  • Fresno Garage Services Safety / Security.
  • Both types of swinging doors are secure.
  • However, the advantage of rolling doors is that they are made of stronger steel, and the parts are assembled.
  • Their parts are usually sealed and include counterweight shafts and springs.
  • On the other hand, partial gates with open springs and cables are more prone to damage; damaged springs will destabilize the gate and can easily cause injury.

 Cost

  • Roller doors can be cost-effective in commercial environments because of their durability and low maintenance requirements.
  • In residential areas where doors are opened and closed less frequently, sectional doors can be more cost-effective.
  • Practicality depends on how the garage roof space is used.
  • In general, garage doors are less expensive, but in the long run, a sturdy, low-maintenance steel roller door will save you money.
  • Maintenance

As mentioned earlier, a bay door has higher maintenance requirements than a revolving door.

Springs, cables, and mechanical parts are susceptible to rust and corrosion and should only require maintenance and replacement if showing signs of deterioration or wear.

In addition, tray doors require regular lubrication or even 40-part maintenance, so in the long run, a roller door will save you time and money. In addition, lubricated springs protect against rust and low temperatures.

How can I limit the opening of my new Gini garage door?

How can I limit the opening of my new Gini garage door
  • Set the limit by pressing and holding the “Limit Open” button until the door is fully raised.
  • Press and release the “Set opening limit” button to save the door position as the new opening limit; the green light will flash twice to confirm.

Troubleshooting automatic garage doors

  • Automatic garage doors are part of many homes across the country and are a popular choice for homeowners who regularly park their vehicles in the garage.
  • Unlike manual doors, they are most often used in garages that are primarily used for storage.
  • Because the proper functioning of an automatic partition door depends on electrical components and various accessories, many small parts can wear out over time. You need to know how to check your doors to avoid costly garage door repairs.

Doors no longer close

If the door starts to move but stops before it reaches the floor and closes, or if the door stops and then reopens, something may be blocking the door sensors.

  • On automatic doors, the sensor lights are located on the rail, usually at knee height.
  • If something blocks the signal or the laser, the door will not close.
  • There is no physical component blocking the signal. The eyes may be dirty and need to be cleaned.
  • If none of this helps, the sensor itself may need a replacement. As a result, you must hire a professional.

The user cannot open the gates.

The most common reason for an operator not opening a gate is a dead battery, but a faulty motor switch or sensor can also cause it.

First, replace batteries and check that it works.

If not, go to the garage and press the switch that opens the door from the inside.

If the door opens with the switch, the fault is in the control unit sensor or the motor sensor indicated by the control unit.

Check that the lenses on both sensors are clean and working properly.

The door cannot be opened with a switch.

If you can’t open the garage door with a switch or operating device and there is light and power in the garage, the fault is in the wiring or switch.

  • First, check the breaker box to see if the garage door switch is fine (aspect).
  • Replace the blown breaker and reconnect it after turning it off.
  • If neither works, remove the hood and look for loose wires.
  • Do this with the breaker off to avoid accidental discharge.
  • If problems persist or if you find bare wires, contact a technician to troubleshoot the wiring problem.

Common Problems with Garage Door Openers

Common Problems with Garage Door Openers

The most common problems with these faucets are

  • Garage door switch does not work.
  • Garage door button latch does not work.
  • Door remote control does not work.
  • Garage door does not close properly.
  • The garage door does not open properly.
  • The garage door motor runs without the door moving.

A garage door maintenance specialist can solve all these problems very easily.

Possible causes of garage door hitting the floor.

  • If your garage door hits the floor, it may be due to one of the following reasons.
  • The subfloor fixing needs some fixings.
  • The garage door’s settings are there to travel a certain distance before closing.
  • Your limit switch needs some adjustments.
  • It would help if you fixed the logic board.

How to Repair a Garage Door that Closes Then Opens Again: FAQs

Why does my garage door close and reopen?

  • Your garage door settings are to travel a certain distance before closing.
  • If it closes before this distance, it assumes something has gone wrong and reopens to prevent damage or safety hazards. You may check the safety sensors.
  • In this case, adjust the “down” setting to the new distance.

Why doesn’t the garage door close?

Most often, the doors are too heavy. Sometime later, the car door handle can be damaged, bent or jammed, so that the door cannot close.

Why does the garage door keep opening?

The fact that the garage door keeps retracting is usually due to a fault in the infrared sensor. If such a problem occurs, one of the sensor’s indicator lights may flash. Sensor failure can be possible by an obstruction, dirty eyes, loose wires, or just a normal sensor.

Why won’t the garage door stay closed?

Most commonly, garage doors do frequently fail to close because the limit setting is not working. This means that the limiter indicates that the garage door is fully open when it closes completely. You may need to try adjusting the garage door limiter setting.

Why does my garage door only open three feet?

  • This problem is probably due to a torsion spring problem.
  • On most doors, you need to replace torsion springs inexpensively.
  • Typically, a garage door service will fix any problem you encounter.
  • If the door closes again shortly after opening, adjust the opener’s force sensors.

Why does my garage door stop halfway?

If your garage door stops halfway, it could mean that something is preventing it from moving. It could be blocked by a protruding nut, a misconnected cable, or something else. Check the tracks and hinges to see if something could be causing the door to lock.

Where is the garage door opener limit switch located?

Some garage door models have limit switches that look like two white buttons on a track. On some models, you will find this one on the opener mechanism. The two white buttons are limit switches that command the garage door to open and close.

Do you have to hold pressed the button to close the garage door?

The problem is due to an obstruction between the sensors, an unclean grille, a loose wire in the sensor or motorhead, or simply a faulty sensor. The transmitter (remote controls) doesn’t work and does not close the garage door. Also, try disconnecting the garage door switch and reconnecting it to the mains.

What is causing the garage door not to open?

Repairing broken springs is one of the most common reasons garage doors won’t open. Garage door extension springs store the mechanical energy that drives garage door movement. Wear and tear can weaken the tension springs and cause the garage door to fail.

What causes a garage door not to close completely?

If the garage door opens properly but does not close all the way, there are three common reasons: the closing limit switch may need some adjustments. Garage doors come with a limit switch that tells the motor when to stop when opening and closing.

How many times can I open and close the garage door?

The service life of an automatic garage door works in cycles, where one cycle corresponds to the opening and closing of the door. Depending on how often you use the garage door, it should have a service life of 10 to 15 years.

Bottom Line

Check if your door is not working properly. So, the first thing you should do is call a garage door maintenance specialist to fix it. In today’s article, we will explain the possible causes of the various malfunctions of this type of door and their solutions. We hope this article has clarified to you “How To Repair A Garage Door That Closes Then Opens Again”

Comments are closed.