How to Wire a Ceiling Fan | A Full Installation Process Guide


Articles, products, and services offered on this site are for informational purposes only. We recommend using caution and seeking professional advice. This site provides general information. We are part of the Amazon Services LLC Associates Program, an affiliate advertising program. is compensated for sales resulting from links on our website.

Please review our disclaimer before taking action based on anything you read or see.

Today installing a ceiling fan is an economical way to reduce your energy bills without sacrificing comfort. However, it’s important to know how to wire a ceiling fan to avoid a disaster down the road. Performing a fan installation can be a perfect weekend project for any do-it-yourselfer. This is because it only takes a few hours to complete, and the result can be noticed immediately. You don’t need to be a home improvement expert to install a ceiling fan. On the internet, you can find a lot of material in which step-by-step explanations on how to perform a good installation.

Below, we will show you how to wire your ceiling fan properly;

How to Wire a Ceiling Fan

  • In the simple procedure for a standard fan, lift the motor assembly.
  • Then place the ball of the rod into the slot in the ceiling bracket. Once this is ready, you will need to rotate it until the fan snaps into place.
  • Then place the wall switch receiver into the mounting bracket.
  • To connect the wires, you will need to hold the bare metal wires together. To do so, place a plastic cable connector over them, and then twist clockwise until the connection is secure.
YouTube video

However, there are four main forms of Fans;

Receiver and wire fan

Next, to connect the ceiling fan wiring system and receiver wires, proceed as follows:

  • Connect the ground wire wires from the ceiling, the wand, and the hanging bracket with a wire nut.
  • Install the white wire from the fan, and on the receiver, the white wire marked “To motor” using a wire nut.
  • Attach the black wire from the fan and the black wire from the receiver device marked “to motor” employing a nut.
  • Attach the blue wire from the fan to the blue wire marked “to motor” with a nut.

Receiver cable and supply line

To connect the supply line and receiver, follow the steps below:

  • At this point, you should connect the black wire from the ceiling to the black wire from the fixture marked “AC In” with a wire nut.
  • Similarly, the white wire from the ceiling should be joined to the white wire from the fixture marked “AC In” with a wire nut.
  • Twist the connections up and push them through the suspension fixture into the outlet box.
  • Divide the connection cables, placing the grounded cables on one side of the outlet box and the ungrounded cables on the other side of the box. Be careful not to pinch the connection cables.

Read More: How To Change Light Bulb In Ceiling Fixture

Wire wall control

To connect the wires to the single wall switch:

  • Remove the switch plate cover and remove all the wires from the switch.
  • Connect the black wires to the outlet box. Attach the two green wires from the socket drawer to the electrical connections of the wall switches.
  • Push all wire connections into the outlet box. Separate the wire connections, with the ground wires on one side of the box and the black wires located on the other side of the same electrical box.
  • Place the wall control unit in the electrical box drawer and secure it using the two screws provided.
  • Attach the switch box cover with the two screws provided.
  • Wiring a ceiling fan with two wires can be a slightly more complicated task. Care must be taken during installation.
  • Another option widely used today is to wire a ceiling fan with light and remote control or wire a ceiling fan with light to a double switch.

Install the canopy

Slide the canopy onto the mounting bracket and align the holes in the canopy with the screw holes in the bracket. Insert the cover screws provided into the holes and secure them firmly.

Assemble and position the fan blades

  • Insert the washers into the fan blade holes. Fasten the blades to the cutter bar using the screws provided.
  • Loosely attach the blade irons to the motor housing with the screws provided.
  • Tighten all screws once all blades are attached.

Housing Switch

  • To wire a ceiling fan to a wall switch, you will need to start by screwing two housing mounting screws into the motor housing. At this point, no matter which holes to place, the screws you choose.
  • Feed the wire supply through the center hole in the top switch housing, then wrap the keyhole slots around the screws and turn it counterclockwise to lock it in place. 
  • Place the third screw and tighten the three screws.

Light kit

  • Connect the plugs on the top and bottom housings of the separate switch. At this point, you will need to make sure the colors are aligned.
  • Lift the lower switch housing and align it over the screw holes in the upper switch housing. Place at least three switch housing screws in the upper switch housing and tighten all screws.
  • Loosen the thumbscrews on the light kit and screw in the glass screen, and then tighten the thumbscrew.
  • Mount a bulb inside or outside the sockets. Note that the installation of the light kit may vary depending on the Ceiling Fan with lights.

Connect the pull chain

  • Connect the pull chain or fan hanger to the short-chain coming out of the switch box.

Wall Control Synchronization

  • Turn on the circuit breaker and the wall switch. Synchronize Ceiling Fan and wall switch (directions may vary by fan model).

Test Fan

  • Verify that the Ceiling Fan turns on and off and operates at all speed settings.
  • Verify that the lights turn on and off and operate independently of the Ceiling Fan.
  • Your fan may include a reverse function. If so, confirm that the fan blades rotate in the opposite direction reversing the airflow.

Using Your New Ceiling Fan

  • Using a ceiling fan in conjunction with your heating and cooling system will reduce energy consumption and increase savings on your home’s utility bills.
  • Some homeowners have reported annual savings of $500.
  • Keep in mind the following: you may sacrifice some time in installing a ceiling fan. However, the savings and comfort justify its use.

Helpful Hints

  • Verify the source of electricity to start working even if you have already tripped the breaker.
  • You can locate a wiring diagram for the ceiling fan on the internet. Many times it can be very helpful.
  • It is important to consider that, although some of the power supplies enter through the circuit breaker (and not from above), the fundamental strategy described here does not change.
  • However, the ceiling fan box can be safely deactivated by turning off the switch.
  • This is useful when replacing ceiling fans with a similar model.

However, we recommend turning off the circuit breaker as a safety mode lest someone try to turn on the lights while you are working.

How to Wire a Ceiling Fan: FAQs

Can you wire a ceiling fan to a light switch?

Most of the new ceiling fans can be connected to a single switch or a double switch.  However, wiring a ceiling fan with light to a double switch is not as easy a task as you might think. With single switch wiring, the fan’s power source is controlled by a standard single-pole wall switch, such as a regular Light Switch. The electrical installation of ceiling fans is a simple task.

Can you wire a ceiling fan with 12 2 wires?

The main obstacle to installing an adjustable switch is the electrical run: standard lighting or fans require 12 – 2 wires, and adjustable switches require 12 -3 wires (14-gauge wire can also be used). That’s the way to wire a ceiling fan with two wires.

Learn More: How To Wire Multiple Pendant Lights

Do ceiling fans need special wiring?

Normally, this calls for a connection between a black to black (hot wire) and a white to white (neutral wire).

Attach any leftover copper or green insulated wire from the fan to the current ground wire and the metal sticky tape.


Many times we can find the installation and wiring of a ceiling fan very “Easy.” The remote control is a key element for this purpose. Many times this works as a guide for the pull chain to work properly.

Learn To Wire A Power Point.

However, if you don’t have a lot of experience installing, this can be catastrophic. In particular, these issues require a fully trained professional in the area who can perform such work. Otherwise, the result can be worse than you think.

Comments are closed.