How to Run Ethernet Cable Between Floors without Drilling | 5 Steps Guide

Computer users were able to place PCs throughout the building without using bulky Ethernet cables due to the implementation of wireless technologies. However, wired Ethernet cables are required. The cable can be run from room to room by a professional, but the cost is frequently prohibitive. To save money on a professional installation, use basic equipment and techniques to run Ethernet wires from floor to floor. Let’s learn how to run ethernet cable between floors without drilling.

How to Run Ethernet Cable Between Floors without Drilling

How to Run Ethernet Cable between Floors without Drilling

Step 1

Measure the distance between the floors you will use for the Ethernet cable. An Ethernet cable will go from one device, such as a computer, to another device. The Ethernet cable runs along walls and floorboards, as well as between floors. Measure the length of all walls and floor panels with which the cable will come into contact. Add 10 feet to the total measurement to allow for miscalculation in the total measurements.

Step 2

Find an access point between floors. The cable will pass through the upper floor and into the basement to the point closest to the unit’s location on the lower level. Find a spot in the corner of the top or along the base of the top. Choose a place as close to the basement wall as possible. Ideally, the location should be directly above the location of the device installed between floors. Avoid places with hard wirings, such as ceiling lights or light switches.

Step 3

Use plastic cable trays along the lining if you cannot hide the low voltage cable under the floor. They are available in various shapes and sizes to fit the length and width of your threads. The running track can be painted with the wall or decorations.

Make your cable ties from a clear plastic bottle to hide the wire around your neck. Cut the bottle into 1-1 / 2 x 1-inch strips, loosen the rim with a small grab bar, wrap the plastic around the wire and push it between the wall and the rim. Install the ghost wire against the wall.

It contains a strong adhesive on one side, which allows easy application between floors. This non-invasive and inexpensive alternative to cutting holes in the wall is this solution of invisible wire.

Step 4

Install the Ethernet cable. Using cable trays, route the cable along the floorboards, starting from the top level. The cable trays have a clip that holds the cable in place and a built-in nail that secures the bracket to the stand’s surface. Install the brackets every 4 feet. Insert the Ethernet cable into the holder and attach it to the wall. Continue until there is an opening between the floors.

Step 5

Mount the cable on the basement walls. Use a cable tray to secure the cable to the wall at the base. Place the brackets at a distance of 4 feet. Connect the Ethernet cable to the devices, and the project is complete.

How to Run an Ethernet Cable from the Bottom to the Floor

How to Run an Ethernet Cable from the Bottom to the Floor

Those who want to run and extend their Ethernet cables from the bottom to the floor are advised to take a proper look at the following simple steps.

Measure the wiring distances:

In the first step, you need to measure the distance between all the devices on the top floor that you want to connect with your Ethernet cable. Keep in mind that your Ethernet cable will go from device to device for proper connection. As a result, you’ll need to double-check each measurement.

Be sure to cut an extra 10 feet to avoid miscalculations during setup.

Locate access points wisely:

You need to locate all the expected access points for your Ethernet cable. Make sure you choose a location as close as possible to the basement wall of your first floor. To make the connection perfect, choose a location just above the default point on the ground floor.

Use a drill:

Now that you’ve measured the wiring distances and located the access points, it’s time to grab a drill bit and start drilling. Be sure to drill exactly 90 degrees while drilling under the ceiling. As soon as the drill bits hit the ceiling, stop drilling.

Start mounting Ethernet cables:

After making the drilled spaces:

  • Start mounting the Ethernet cables using the cable tray.
  • Using mounting cable clips, hold and place the cable in the position of the built-in nail to secure the cable holder to the ground surface.
  • Continue to place the Ethernet cable in the cable holder until you reach the top floor.

Finally, connect the devices to Ethernet:

After straightening the wire socket, begin threading the cable through the hole. Glue your Ethernet cable to the right with the length and thread the cable through the hole drilled in the ceiling. Remove the Ethernet cable, connect the devices to the cable, and you will be able to run your Ethernet cable from the bottom to the floor.

Frequently Asked Questions

How to run an Ethernet cable between floors?

Drill a destination hole in the ground. Thread through the hole. Thread the wire through the socket’s back, insert the box into the wall, and mount it in place. Remove the wires and plug them into a wall outlet or point them at the device.

How can you run wired internet upstairs?

Plug the Power line adapter into a wall outlet near a modem or router and plug one Ethernet cable into it. Then, in any room where you want to have an Internet connection, connect another Power line adapter, and then use an Ethernet cable to establish a connection between the adapter and the device.

Is Ethernet faster than WIFI?

Ethernet is generally faster than Wi-Fi and has other advantages. A wired Ethernet connection is more secure and stable than a Wi-Fi connection. You can easily test the speed of your computer via a Wi-Fi connection versus an Ethernet connection.

How to run an Ethernet cable through a finished house?

You can use the inside of the cabinet as an opening. Route the cable to the cabinet in line with the wall on the second floor (good) or the cabinet on the second floor (better) and pull it along the wall inside the cabinet. On the inner wall, the door is cut, so you can’t see the wire even if you look in the cabinet.

Is it worth using an Ethernet cable?

Assuming it’s easy enough to connect devices with an Ethernet cable, you’ll end up with a stronger and more cohesive connection. Ultimately, Ethernet offers the benefits of better speed, less latency, and a more reliable connection.

Conclusion

People generally find that Ethernet is more reliable and faster than a Wi-Fi connection, which is why they are always looking for several ways to expand their Ethernet connection. However, the whole procedure can be done by a technician, but why bother with paying the installation fee when you can do it yourself using tools and simple steps.

Comments are closed.

buy cialis online cialis online