How to Remove Sand Texture from Walls | 24 Steps To Follow By Expert

A considerable amount of people commonly asks themselves how to remove sand texture from walls?

Sand textured paints are designed to hide inferior deficiencies and add a suede look to walls.

There are numerous configurations available for removing these paintings. Some are extreme, such as eradicating the Sheetrock, but others are less expensive. All involve patience and a dust mask.

If you are not a follower of the texture on your walls, you have some configurations. One alternative is to try rubbing the texture with water and a floor scraper or drywall knife. The second alternative is to look at the texture with joint compound, which needs numerous coats.

A second procedure is more time consuming, as it may require many coats of joint compound, and you may have to let it dry overnight between coats. Wall texture removal can be a topic you’ll want to leave to the experts unless you want to do it on your own

The most important thing before starting is sanding textured walls before painting to have a better result. Somehow, the job is difficult, so be sure to prepare the area with tarps and cloths before you begin.

How to Remove Sand Texture from Walls: Materials Required

• Protective eyewear
• Breathing mask
• Tarpaulins, old sheets or rags
• Plastic covers
• Painter’s tape
• Spray bottle
• Floor Scraper
• Sandpaper
• Protective glasses
• Fast or ultra-light jointing compound
• Board Knife
• Empty
• Drill with mixing attachment
• Roller
• Paint tray
• Water

How to Remove Sand Texture from Walls

Preparing your workspace

Step 1: Covers the room’s furniture

This work is complicated. You will have plaster and paint everywhere, so make sure everything is acceptably covered. Take look at the furniture with old sheets, protective fabrics, or tarps.

You may also want to look at the vents so they don’t extend throughout your home. You can cover them with plastic tape to keep dust out.

Step 2: Move furniture if you are nervous about dust.

If you’re worried about damaging your furniture, it’s best to remove it from the room. Finally, you should remove any fragile or old parts from the room, if feasible.

Step 3: Put tarps on the floor

If you want to reduce your cleaning, put tarps or rags on the floor. That will help contain the chaos, so you can pick it up and take it somewhere else, away from your feet. Tape the tarp close to the edges with masking tape.

Step 4: Protect yourself with a safety kit

• Wear your safety equipment to be covered from debris.
• If you are concerned about lead paint, consider using a respirator instead of just a dust mask. You can also wear gloves when applying joint compound.
• If you have an older home, you may have to deal with lead paint. In that case, you’ll need to take extra precautions, such as removing everything from the room or covering it with two sheets of plastic, all 6 millimeters thick.
• You should also use disposable clothing or coveralls, enclosed with gloves, goggles, a respirator, and a hair cover. Vacuum the dust with a vacuum cleaner with a filter.

Step 5: Spray a small area with water

• Start with a square of 0.61 by 0.61 m (2 by 2 feet) and cover it well with water. Do not spray a large area yet, as you will need to train a little to control the technique. Allow the water to penetrate the wall for a few minutes. The water will help make it easier to rub the texture.
• Check out if it is wet enough. You should feel a little slow.
• If it doesn’t look soft, try respraying it.

Step 6: Hold a floor scraper or drywall knife at a 30° angle.

Put the paper against the wall. The form should make a 30° angle coming out of the wall. Keep it permanently at this angle when you start rubbing.

Step 7: Scrape the texture

Scrape the wall at an angle, adjusting it as you go. You may need to rub harder or slower, depending on how the wall responds to your scraping. That’s why you start with a small space first.

If the texture does not come off, you are not rubbing hard enough. 

Step 8: Move around the room in small parts.

Spray a different section once you find your groove. It could be more significant than your opening statement. As previously, soak it and clean it. Till all of the texture is gone, keep moving around the space.

Make care to wander around the space methodically to avoid missing any areas. Pick a place to begin. Imagine how the whole room would seem, as if it were moving up and down the wall.

Add additional water if it starts to dry out since it’s necessary.

Step 9: Sand the remaining texture

• When you have finished the entire room, rotate with medium-grit sandpaper in the 60 to 100 grit range.
• You can also use a sanding display.
• Do not sand too hard, as you will not want to sand through the paper on the drywall or plasterboard.

Step 10: Clean the wall with a damp sponge

You don’t want to leave dust in the area, so wet a large sponge. Clean the wall as much as you can to remove the dust. You may need to wash the sponge occasionally.

Step 11: Apply joint compound to the wall with a drywall knife

Use a drywall knife that is 6 inches long to spread the joint compound on the wall. Aim for a 3.2 mm ( 1 ⁄ 8 inch) thick deck. Smooth it on the fly, and be sure to fill each wall in one session to give it a more tailored look. Allow the wall to dry overnight.

Step 12: Sand the walls again

After the wall has dried overnight, sand the rough surfaces with medium-grit sandpaper or a sanding display. Create as smooth an area as you can get.

Vacuum the dust from plasterboard so it does not float in the joint compound when you reuse it. You can use a level vacuum, but make sure it’s excellent. You can also rent a drywall vacuum specifically for that purpose.

Hold a floor scraper or drywall knife at a 30° angle. Place the paper against the wall. The paper should make a 30° angle coming out of the wall. Keep it permanently at this angle when you start rubbing.

Step 13: Apply another round of joint compound

Use your drywall knife to use the second and latest joint compound cover. This time, make a thinner cover since you are primarily trying to fill in the low spots. Let it dry overnight.

Step 14: Sand again

• After the joint compound has dried overnight, take time to flatten the walls again.
• Pass medium-grain sandpaper over rough surfaces to make a smooth area. Vacuum the dust.
• Assist in cleaning the wall with a damp sponge again, allowing it to dry out later.

Step 15: Print the wall

Before coloring, apply primer to the wall. Use a paint roller to use your selection paint base, creating the ideal canvas for any painting you choose.

You can paint the wall very quickly. However, you must take into account specific considerations.

Step 16: Mix your joint compound

For this procedure, you require your jointing compound to be like crepe batter. Even if you are using a premixed compound, it is feasible that you will need to add some water to dissolve it a bit.

You can use a metal mixing attachment. You can do this for a level drill. However, you may have to combine the water in batches since this kind of mixer is usually not strong enough to connect the whole bucket at once.

Step 17: Pick up the compound with a bulky paint roller.

Pour some of the compounds into a roller coloring tray. Roll a paint roller in it, covering the roller with the combination. Try to carry it out in a suit.

Step 18: Roll the compound on the wall

Do this job near the room in small parts of precisely one by 2 feet, use the paint roller to apply the compound to the wall. Move from top to bottom and subtly overlap each piece. As you move forward, keep the edge adjacent to the next part wet. If required, spray with a small amount of water.

Step 19: Smooth the compound with a trowel on the fly

Moving up and down, create a suit cover with a palette. Smooth out each little part as you go; don’t wait until the entire wall is finished. Get it as slow as you can, but concerning how thick the texture is, this cover may not be prolonged

Step 20: Allow the joint compound to dry.

The joint compound should dry overnight before using the next cover. When you have softened it, let it dry.

Step 21: Sand as needed

• If you see transparent surfaces that are rough or protruding, you can try sanding them down a little with medium-grit sandpaper. Vacuum the dust and wipe the wall with a damp sponge to remove the dust.
• Use a vacuum cleaner to sand plasterboard to reduce the chaos.
• Try 60 to 100 grit sandpaper.

Step 22: Repeat layers as needed

Continue to add layers of joint compound to the wall, allowing it to dry between coats. Sand when required. Add enough coats to hide the wall texture. You may need to do 3 to 5 coats to see the surface.

Step 23: Sand the wall with fast grit sandpaper

• When you have covered the texture, run it over the wall with quick grain sandpaper to smooth it. Do not press hard, as this will create more texture. Clean it with a damp sponge to remove dust and vacuum any remaining dust.
• Try using sandpaper in the 120 to 220 grit range.

Final step: Apply primer to the wall

At this time, you need to elaborate on the wall to color. You can apply it with a paint roller, covering it evenly to make a smooth area for your painting.

The texture on the walls is one of the essential things of all this.

How to Remove Sand Texture from Walls: FAQ

Is it possible to flatten textured walls?

The development of flattening of textured walls with a skimmed coating is widespread. It is related to extending a joint compound cover over the walls to complete the texture bumps and valleys, successfully creating a smooth area.

How are roughly painted walls sanded?

To paint from the water before painting:

• Sand with fine grain sandpaper.
• For paint from oil, use medium-grain sandpaper (100 to 150 grains).
• Again, clean some residue and let it dry completely.

Are textured walls outdated?

Only some of the textures on the wall are outdated, the “dugout” look. Yes, it’s true; some trendy designers and artists are rubbing the wallpaper and surface to showcase authentic plaster walls or artistically mimicking the look. Peeling wallpaper, with some still attached, also works in this area.

Conclusion

We can say that these kinds of walls in several cases have the possibility of appearing old-fashioned and so on. On the other hand, it is not this way. If you want to remove this style of painting from your wall, what stands out is. Painting over sand textured walls can be useful in some cases. However, it can be a long process to remove it. Textured wall removal can significantly help the aesthetics of the house and give you a better view.

Read More: How to Clean Stone Shower Walls