How to Clean Grout between Marble Tiles | DIY Cleaning Guide

Marble and grout are very easy materials to maintain when a proper cleaning routine is applied. It is very important to obtain components that clean effectively but are gentle enough not to damage either surface. That’s why today we bring you how to clean grout between marble tiles.

Even after cleaning, tile floors with dirty grout still look dirty.

Fortunately, you can easily clean the grout with simple household products to make your tile look new again.

How to Clean Grout between Marble Tiles: Tools Needed

For this, you will first need tools such as;

How to Clean Grout between Marble Tiles: Steps

Method 1: Using baking soda and Vinegar

  • Make a paste of baking soda and toilet water.
  • Mix 4 parts baking soda with 2-part water to make a thick paste.
  • These acidic cleaners work with all grout colors. However, Vinegar is harmful to some natural stones such as marble.
  • With your finger, apply the paste to the grout stripes.
  • Although baking soda is not harmful, wearing rubber gloves can help prevent scratches or irritated skin from abrasive grout and baking soda.
How to Clean Grout between Marble Tiles

Apply a vinegar solution to the baking soda grout

  • Prepare a mixture of equal parts water and white vinegar and pour it into a spray bottle.
  • Then, spray the baking soda into the vinegar solution. You should immediately see a bubbling sound, letting you know that the natural cleaning procedure has started.
  • If your stone tile is natural, it is not recommended that you use Vinegar.
  • When you see bubbles, it means that the baking soda and Vinegar are already doing their chemical reaction.
  • The reaction usually lasts for a few minutes. Once the bubbling has stopped, the chemical cleaning action takes place.

Scrub grout lines with a brush

  • Use a nylon bristle scrub brush or scrub brush along the grout lines.
  • Pay attention to the corners and edges and clean those areas as well.

Mop the floor with water

Use a mop and water to remove the baking soda and vinegar residue.

Rinse your mop and change the water frequently during the cleaning process so you don’t continue to spread the residue on the floor.

Method 2: Cleaning grout with oxygen bleach

steam clean marble grout

Dissolve two tablespoons of oxygen bleach in 2 cups of hot water

  • One of the best grout cleaners for natural stone is Bleach.
  • Prepare the solution immediately before use for best results.
  • Mix the solution well to make sure the oxygen bleach is fully activated.
  • Oxygen bleach has power, which may damage colored grout, but is mild enough for all types of floor tile.

Before cleaning the floor, test a hidden part of the grout.

  • Some floor tile or grout may bleach or discolor with oxygen bleaching.
  • To test the grout’s colorfastness, apply a small amount of the oxygen bleach solution to an inconspicuous section of the grout.
  • Pour the oxygen bleach solution over the grout. Be sure to pour enough to cover the grout lines completely. To avoid having a completely wet floor, you need to clean one section of the floor at a time. 

Pour the oxygen bleach solution over the grout.

  • Be sure to pour enough to cover the grout lines completely.
  • To avoid having a completely wet floor, it is necessary to clean a part of the floor.
  • For scrubbing, bleach mixture into grout lines uses a nylon bristle brush.

For optimal results, it is necessary to allow the oxygen bleach solution to settle in.

  • Pass the brush back and forth in the grout.
  • Don’t forget to scrub the corners and around the edges of the floor, as dirt and grime tend to accumulate here.
  • Dip the brush in oxygenated bleaching powder to increase the cleaning power.
  • If you find a darker or more noticeable stain, you can prepare a stronger oxygen bleach solution by dipping your wet brush directly into the oxygen bleach powder.
  • To prevent water from mixing with your main container of oxygen bleach powder, pour a small amount of powder into a separate container.

Rinse the floor with water and wipe dry

Pour clean water directly onto the tile floor and dry it with a clean towel or mop.

Bleach is a stone-safe grout cleaner, which can help you and make a lot of work easier.

Method 3: Clean the grout with dish soap, hydrogen peroxide, and finally with baking soda.  

marble cleaner

Create a kind of paste

  • Mix ¼ cup hydrogen peroxide, ¾ cup baking soda, and one tablespoon liquid dishwashing soap.
  • This highly effective paste cleans grout in three ways:
  • The baking soda works like a natural abrasive to scrub the grout.
  • Sodium bicarbonate reacts chemically with hydrogen peroxide releasing bleaching oxygen ions.
  • One product that can help you loosen dirt and remove grease is dish soap. 
  • The bleaching reaction of the chemical may affect the colored grout. Test in a hidden corner of the floor before cleaning the entire floor.

Apply the paste with a nylon bristle brush

A toothbrush or nylon scrub brush works well.

Apply the paste to the grout around the edges and between all the tiles to get a uniform and clean appearance.

Allow the mixture to settle for 15 minutes.

You may see a bubbling reaction when the baking soda and hydrogen peroxide interacts. Give the paste time to work into the grout to remove stains on the marble completely.

To remove all solutions, rinse the grout with warm or hot water. 

  • To rinse the grout solution, pour a small amount of water directly onto the tile floor. 
  • Be careful as wet tile floors can be very slippery.

Use a rag to wipe off the grout and remove any remaining residue or dirt.

  • Wipe the remaining grout paste by gently rubbing the floor with a cloth.
  • This can be done by dragging the fabric on the floor with both feet.

Mop the floor with clean water

  • Ensure there is no soap or residue by thoroughly mopping the floor with a cotton mop or sponge.
  • For a clean finish, change the water frequently and rinse the mop.
  • Another simpler option is to use grout and tile cleaner.

Method 4: Cleaning grout with a steam cleaner

grout cleaner

Rent or purchase a steam cleaner

  • Steam cleaners can effectively clean and disinfect all tile and grout types, as they contain no chemicals.
  • To find a machine for rent or sale, please visit your local store.
  • Make sure the steam cleaner you purchase has the proper accessories for cleaning grout:
  • Steam hose
  • Small brush attachment

Follow the manufacturer’s instructions for assembling and filling the steam cleaner.

To avoid causing damage to the equipment, it is necessary to read the instructions carefully.

Fill the tank with clean water up to the fill line according to the instructions in the manual.

  • Do not add soaps or chemicals to the water tank of the steam cleaner.
  • The steam cleaner’s instruction manual will tell you how long to wait after turning on the machine before cleaning.

Move the brush over the grout.

  • May start on one side of the room and move toward the other end of the room.
  • The steam will lift dirt and grime from the grout and kill any mold and mildew present.

Use a mop for scrubbing excess moisture after cleaning.

  • Steam cleanings will remove all grout sealers, so only use a steam cleaner if your grout is not sealed or if the sealer is old and you are ready to remove it.
  • For many, the solution is steam-clean marble grout. However, not everyone has these devices that make your life simpler. Products around marble are usually very good for stains.

How to Clean Grout between Marble Tiles: FAQs

What cleans the grout between tiles?

  • Scrub the dirty grout with warm water and a stiff bristle brush.
  • Spray with equal parts of warm water and Vinegar for a few minutes.
  • Apply a paste of baking soda and spray with Vinegar.
  • Pour a little hydrogen peroxide.
  • Apply Oxygen bleach for 10 minutes.
  • Try a commercial product.

What is the best way to keep marble pieces clean?

  • Start by regularly sweeping marble floors to keep dust and dirt away.
  • Use a soft broom to sweep up dirt and dust particles. Mop or wipe with mild cleaning agents such as baking soda or non-phosphate detergents.
  • Rinse using a clean, damp soft cloth, then wipe dry.

What kind of grout do you use for Penny tiles?

Unsanded grout is more of a fine powder and is best used in 1/16 inch spaces. Because of the pennies’ shape and location in the penny sheets, the smallest space where the pennies are closest together is about 1/16 inch, BUT the rest of the spaces between the pennies are larger, hence the need for sanded grout.

Conclusion

The grouts of natural stone tiles are a little delicate. If you do not know how to apply the products, it is possible to ruin your tile. Your floors can be well cared for if you do your routine maintenance at the right times.

You must leave it in specialists’ hands if you are not trained for this work.

Read More: How To Clean Unfinished Wood Floors

Comments are closed.